One rhythm. A whole sound in motion.
Arrange sonic actions in Rhythm, link effect parameters with four LFOs, and shape every connection in Matrix. From sharp cuts to slowly unfolding space, compose the movement inside your sound.
macOS 13+ · Apple Silicon / Intel · AU · VST3 · Standalone
One LFO. A whole chain in motion.
Open the filter, push the drive, introduce an echo and spread the space with one envelope. Four independent LFOs offer up to eight destinations each, with individual ranges and directions. Tone, rhythm and space move as one gesture.
Write effects into the beat.
Rhythm arranges sonic actions: paint repeats, ratchets, reverse, half-time, tape stops and spin-ups. Schedule when a module appears and which type it uses. Set cell duration independently of cell count, from tight sixteenth-note cuts to longer fills.
See every connection. Shape every range.
Each Matrix row shows one LFO-to-parameter connection. Change its source or destination, drag range endpoints and watch the live position and value. Select an LFO card to focus its routes while editing the envelope alongside them.
Draw sharp cuts and flowing curves.
Hold with a flat segment, switch at a vertical edge, build with a ramp and bend the curve between points. Combine them in one loop: keep the opening clean and bring effects in more insistently toward the end. Choose sine, steps or a drawn envelope to suit the sound.
Nudge a parameter. Or take it over.
Mod adds movement around the value you set. Remote drives a parameter between two chosen values. Use different modes on different destinations of the same LFO, including inverted ranges: open the filter while pulling the echo back.
The grid sets the moment. The LFO shapes it.
Place reverse on the final two cells in Rhythm while an LFO moves filter and delay parameters. A step LFO mapped to a module’s Mix can bring it in on selected beats; mapped to a continuous parameter, it can give each step a different intensity. Arrangement and modulation work together.
Turn a loop into a live fill.
Hold Fill to play a variation and release it to return to the main rhythm, or latch it on. Roll the whole rhythm or a single row, then edit the result cell by cell and undo freely. Find a surprise, then keep the accents that matter.
Move more than volume.
Combine Pitch layers, Lofi media, Robot and Drive shaping, Filter and Motion movement, then Delay and Space. Reorder the chain to change how the effects interact. Independent low and high cuts in Delay and Space give that movement its own frequency range.
Bring a complex patch under one control.
Scale the strength of LFO mappings with Amount while keeping their destinations and individual ranges. Pull it back for a verse and push it for a fill. Mix controls the dry/wet balance; Amount controls how strongly the parameters move.
Start with the movement you need.
Browse 14 categories spanning gates, reverse, tape stops and scratches, transitions, harmony, filters, modulation, delay and space. Keep shaping the Rhythm, envelopes and Matrix after loading a preset. Compare two versions with A/B, or build from Default.
Sound demos
Producer demos coming soon.
System requirements
- Operating system
- macOS 13 or later
- Processor
- Apple Silicon and Intel Mac
- Plug-in formats
- Audio Unit (AU) and VST3
- Where to run it
- Use a host that supports AU or VST3, or open the standalone app.
Frequently asked questions
How do Rhythm, LFOs and Matrix work together?
Rhythm places actions on the timeline, such as reverse on steps 15 and 16. An LFO shapes a parameter over time: hold a cutoff steady, then open it quickly. Matrix defines the destinations, ranges and directions of that movement. To build a fill, arrange reverse in Rhythm, then map one drawn LFO to Filter Cutoff and Delay Mix with opposite ranges in Matrix. In sync mode, check the Rhythm cell duration and cell count separately from the LFO cycle length and phase so their movements meet at the intended beat.
How do I reverse just the last two steps?
In Rhythm, set up one bar with 16 steps and paint Reverse on steps 15 and 16. Leave the earlier time-effect cells empty. Reverse engages when the playhead reaches the last two steps.
Can I open the filter while pulling the echo back?
In Matrix, route one LFO to Filter cutoff and Delay Mix. Set both routes to Remote. Use a rising range for cutoff and a falling range for Delay Mix. The same envelope now moves the two controls in opposite directions.
How can I soften the movement and keep my wet/dry setting?
Lower Amount at the top of the plug-in. The mapped parameters move through a narrower range together. Leave global Mix where it is, and adjust it when you want to bring back more dry signal.
How many parameters can one LFO control?
Each of the four LFOs can drive up to eight targets, giving you 32 routing slots. Set the range and direction on each route and watch its current value in Matrix.
Can I keep a rhythm and reroll just one row?
Yes. Click the die next to a Rhythm row to regenerate that row. Click individual cells to keep an accent or change a hit, or undo the last edit.
The envelope moves, but I hear little change. What should I check?
First check that the effect is enabled and that its Mix and the global Mix actually include the processed signal. Check Amount next: it may be scaling the movement down. In Matrix, verify the destination, separation of the range endpoints and live parameter value. Remote defines an explicit range; Mod adds movement around a base value, so an animated waveform alone does not guarantee a strong audible result. Match timing to the material: start with synced 1/4 or 1/8 and step or drawn hold segments for rhythmic cuts; use slower sine motion for continuous modulation. In Delay and Space, check feedback, decay and low/high cuts too. Long tails can obscure the cuts, while a narrow frequency range can hide the change.
Try Motion in your session.
Install BUDGIE HUB, sign in and start your 14-day Motion trial.